1. كل المواضيع تعبّر عن رأي صاحبها فقط و ادارة المنتدى غير مسؤولة عن محتوياتها
    إستبعاد الملاحظة

pour walid merci 1page sur 2

الموضوع في 'English & French Archive' بواسطة zsisous, بتاريخ ‏11 جوان 2006.

حالة الموضوع:
مغلق
  1. zsisous

    zsisous عضو مميز

    إنضم إلينا في:
    ‏23 نوفمبر 2005
    المشاركات:
    600
    الإعجابات المتلقاة:
    18
      11-06-2006 12:44
    voila directement de al7bar es autoupdate de tps ou pas une reponse de ta part merci il a 2 pages 277t STEP BY STEP INSTRUCTIONS, HAVE QUESTIONS LOOK HERE BEFORE YOU POST
    Friends are like a head of hair. You might lose some but with enough money you can buy them back.

    277t has Auto-Key & Auto-TP-Roll & Bev, Safe For All Fortec Lifetime Ultra Clone's & Pansat 2500a. This is NTSC not PAL
    Read all of these instructions and you will have less questions and may learn something.
    TP auto-roll will find a channel if it is moved. It will NOT find the channel if it moves to another Satellite.

    PLEASE DO NOT PM ME WITH QUESTIONS, POST YOUR QUESTION IN A NEW THREAD.

    YOU CAN PRINT THIS OUT IF YOU LIKE
    To print this out in a printable version go close to the top of this thread and click on THREAD TOOLS then click on SHOW PRINTABLE VERSION then click on PRINT in your browser . From time to time I will edit this. By looking at the bottom left of this page it will show you when it was edited. You can compare the date with your copy. You can PM me with any ideas you may have that will help others. PLEASE do NOT PM me with questions that can be asked by posting them. Only PM me if there is something I should add, take away or change in these instructions to help others, Thanx.

    I am NOT taking credit for this bin just the instructions. Chancysand & others get the bin credit.

    PLUGGING IN CABLE.
    Make sure you plug in the cable from the dish to the receiver at the IF 13/18v INPUT. Not the ANT IN. Change the FTA to ALL just before you scan for channels. Also the wires coming from the dish to the switch should be put on the switch at the same number as you have set in your receiver. Like 119 wire goes on number 1 on the diseqc switch and the receiver has #1 for 119 in the program.

    HOW TO FLASH FORTEC LIFETIME ULTRA.
    You can flash (load) your Ultra with this bin on top of the bin (file) you already have. It will replace it.
    Use a STRAIGHT THROUGH CABLE RS232C hooked up to your receiver from the computer. Take the cable off going to the LNB to be safe.
    If you have the year model Dec 2004 or newer you can clone it or you MAY need to use a USB to Serial cable 26-183 at Radio Shack. Get detailed instructions about the cable here http://www.beaglesoft.com/232usb.htm
    Download the recommended file X-85BL_060610_277t_au_api.zip
    You can get it here http://forums.al7bar.tk/showthread.php?t=160602
    Download a loader, BLACKLIST UP LOADER.ZIP It don't ask as many questions.
    You can get it here http://forums.al7bar.tk/showthread.php?t=135458
    UNZIP both files. You can use WinZip or Winace.
    You can get them here http://www.winzip.com/ http://www.winace.com/
    Click on BLACKLIST UP LOADER.EXE to start it. Set the COM PORT and select the word BIN.
    Click on BROWSE then put in the bin you want (note it is a bin & NOT zip)
    Turn receiver on from the back, when FIRST bar starts then click FIX on our computer.
    After you get compleat at the computer the ON will display in your receiver. Your receiver is flashed.
    If you get (Night Rider) NR ------- dashes instead of the ON then flash with the 276 Factory bin to bring it back and start over again. You can get the 276 bin here below. Some Ultra's need to flash with the 276 bin before they flash with a new bin or they will get a NR. You can also use the 228 factory bin to bring back your receiver.
    http://forums.al7bar.tk/showthread.p...872#post762872
    If you have no lights (NOTHING) on your receiver then you will need to jtag.
    You can go below for some jtag help.
    http://forums.al7bar.tk/showthread.php?t=96780

    DISH ALIGNMENT
    Alignment on your dish is very critical and could be frustrating. You are looking for a signal from a Satellite that is about the size of a small van over 1,000 miles away. You want a high QUALITY signal before you start to scan, that is the green bar. above 90 is good above 95 is better. Below you can find a program that will tell you what your dish settings should be. There are many programs, below are just some. The program will get you close the rest will be up to you. Hook the dish cable to your receiver at the IF connector NOT the ANT. If you have a Dish Pro LNB or do not have a 22Khz switch then you can keep the 22Khz switch OFF in the settings, but it don't care. If you have a Dish Pro LNB you may want to change the LNB type to Dish-Pro, below has STANDARD not for a DP. Go to SETUP in the receiver and pick a Satellite you want. Run the cable straight to the LNB with no switch if you have one and if you can. Have someone look at the QUALITY SIGNAL on the TV as you move the dish less then 1/8th of an inch at a time. You can only get one Satellite for each one LNB you have. One LNB one Satellite. Two LNB's two Satellites, and so on. If you are going for two Satellites then you need to adjust the SKEW. The skew is adjusted like when you turn the steering wheel on a car. If your Quality signal is much lower on one Satellite then the other on the same dish then your skew is off. Equal signal on both Satellites would be good.

    A MENU SETUP Below FOR 110 & 119 & Nimiq 1,3 91.0W SATELLITES WITH TWO SEPARATE LNB's & ONE DiSEqC OR A 22Khz SWITCH. Or A DISH PRO LNB, and no motor to move the dish
    YOU MAY NEED TO FIX YOUR SATELLITE SETTINGS AFTER A FLASH & SET THE DEFAULT KEY.
    The TP's below are close and will give you the channels that are there.
    MENU to INSTALLATION then OK then OK in ANTENNA SETUP, then to the Satellite you want then OK.
    ----------------ECHO 7 = 119-----ECHO 6,8 = 110-Nimiq2=Nimiq 1,3 91.0W or Bev
    LNB type --------- Standard ------------- Standard--------------Standard
    LNB local-Freq ---- 11250------------------11250-----------------11250
    22Khz -------------- ON----------------------Off--------------------OFF you can only have two satellites with this switch
    DiSEqC -------------- 1------------------------2----------------------3
    SKEW --------------- 0 -----------------------0----------------------0 this setting is if you don't have a motor to move the dish.
    TP ------------ 12224V20.00-----------12224V20.000--------12224V20.000
    Positioner Setting -- Disable----------------Disable--------------Disable
    Satellite Scan ------ ALL----------------------ALL-------------------ALL

    HOW TO SET DEFAULT KEY.
    MENU, PARENTAL CONTROL, OK, down to SECOND PIN put in 0000 or 1010 or 1668 then OK then down to SET DEFAULT KEY then OK.

    HOW TO DO A FACTORY SETTING
    MENU, down to FACTORY SETTING then OK. When you do this you will clean out your channels.

    You will get more channels if you do a Satellite scan with ALL. You can use Channel Master to sort, get channel numbers, rename & much more. Save them under Fortec Lifetime Ultra. Channel Master is one if the best. For instructions in CM click on HELP. You will get ONLINE SUPPORT there.

    TP SCAN HOW TO
    MENU, then click OK in INSTALLATION, then down to TP SCAN, then OK, then pick a Satellite, then OK, then pick a TP you want to scan and click OK. All the channels you get will be at the end of the list you already have.

    AUTO-ROLL OPTIONS
    You can turn auto-roll ON or OFF in DN, Bev & or GlobeCast. YOU NEED TO KEEP KEYCODE ON. Don't turn KEYCODE off or it will not look at any keys & TV will not work.
    MENU then PARENTAL CONTROL then OK then to bottom at SECOND PIN then 1668 or 1010 or 0000
    then down to AUTOROLL OPTIONS then OK. Side arrow will change autoroll then OK then EXIT.
    To turn TP AUTOUPDATE ON or OFF go here. MENU, then down to USER SETUP then OK then down to TP AUTOUPDATE, side arrow will make the change. then EXIT
     
  2. jerba4135

    jerba4135 عضو نشيط

    إنضم إلينا في:
    ‏16 مارس 2006
    المشاركات:
    169
    الإعجابات المتلقاة:
    1
      11-06-2006 13:55
    Copier =====> Coller
     
  3. zsisous

    zsisous عضو مميز

    إنضم إلينا في:
    ‏23 نوفمبر 2005
    المشاركات:
    600
    الإعجابات المتلقاة:
    18
      11-06-2006 14:44
    sa ve dire kois?:85: esseye de comprendre avant de dire n importe kois
     
حالة الموضوع:
مغلق

مشاركة هذه الصفحة

جاري تحميل الصفحة...